Presentasjon lastes. Vennligst vent

Presentasjon lastes. Vennligst vent

Bilder fra 2 – 7 viser hovedkomponentene i en snubbing opprigg.

Liknende presentasjoner


Presentasjon om: "Bilder fra 2 – 7 viser hovedkomponentene i en snubbing opprigg."— Utskrift av presentasjonen:

1 Bilder fra 2 – 7 viser hovedkomponentene i en snubbing opprigg.
Bilde 8 er et eksempel på en opprig fra Statfjord Bilde 9 viser skjematisk opprigg av snubbing på Statfjord Når vi er i bilde 2 BOP system bør en kunne klikke på figuren og en sjematikken i fig 10 kommer frem. I figur 10 må en bør en kunne klikke på figuren og komme til detaljer for anular (fig 16), ram ventier (fig 17 og 18) og stripper (fig 19). I fig 3 må en når en klikker på det komme til bilde av arbeidsvindu nr. 15 I fig 4 bør en ved å klikke på hydraulisk jekk komme til bilde som viser hovedkomponenter i hydraulisk jekk (fig 11) og bilsd av hydraulisk jekk (fig 12) samt til bilde 13 lederøret som montereres i hydrauliks jekk. I fig 5 arbeidsbasket bør en når en klikker på bildet komme til bilde av arbeidsplattform (bilde 15) Basic equipment consists of a set of Snubbing or Drilling BOPs nippled up directly on to either the tree or wellhead as dictated by the proposed operation. (I will talk more about the BOPs shortly)

2 Oppriggskomponenter BOP System
Basic equipment consists of a set of Snubbing or Drilling BOPs nippled up directly on to either the tree or wellhead as dictated by the proposed operation. (I will talk more about the BOPs shortly) HYDR. HYDR. HYDR.

3 Oppriggskomponenter BOP’s Arbeids vindu
On top of the BOPs is installed a ‘work window’ which can vary in height but is normally either 5’ or 10’ tall. This window allows for the handling of components and assemblies (such as stabilisers or tubing hangers) that are too large to pass through the Snubbing Jack. Depending upon the operation, sets of stationary slips are either situated in the work-window or in the bottom of the jack in order to support the static weight or the workstring and components. HYDR. HYDR. HYDR.

4 Oppriggskomponenter BOP’s Arbeids vindu Hydraulisk jekk
Above the work window is the Subbing Jack itself which consists of four hydraulic cylinders to convert the hydraulic forces required to pull or push the workstring. On top of theses cylinders - on what is in know as the travelling head -are two sets of (travelling) slips which are basically the equivalent to the elevators for a conventional drilling rig. One of the sets of slips is inverted for when the pipe is in the pipe-light mode. i.e. if unrestrained the well pressure would force the workstring out of the well. In addition to the travelling slips the travelling head also incorporates a hydraulic rotary table which allows the string to be rotated. This rotation can be applied at all times, that is when pulling or pushing if required. HYDR. HYDR. HYDR.

5 Oppriggskomponenter BOP’s Arbeids vindu Hydraulisk jekk Arbeidsbasket
The workbasket forms a safe platform from which connections can be made and the BOPs can be controlled. HYDR. HYDR. HYDR.

6 Oppriggskomponenter BOP’s Arbeids vindu Hydraulisk jekk Arbeidsbasket
Rørhånteringssystem The last major component in the stack-up is commonly refferred to as the ‘gin-pole’ which is a telescopic mast which, in conjunction with a counterbalance winch and a tail-out sheave (not shown), allows joints to be safely delivered to the work basket. HYDR. HYDR. HYDR.

7 Oppriggskomponenter BOP’s Arbeids vindu Hydraulisk jekk Arbeidsbasket
Rørhånteringssystem HYDR. HYDR. HYDR.

8 Statfjord opprigg Rørhåndteringssystem Arbeidsplattform
Stilas rundt jekk Trappetårn Catwalk Rør

9 Statfjord opprigg Jekk Stripper bowl Stripper Annular Variabel bor ram
Shere / blind ram Pipe ram Safety head

10 BOP system Primær trykkontroll Sekundær trykkontroll
Snubbing Jekk Primær trykkontroll Stripper BOP’s Stripper rubber/stripper bowl Equalize line & bleed line Annular BOP Sekundær trykkontroll Upper pipe ram Lower pipe ram Choke/kill valves Tertiær trykkontroll Blind/shear ram Shear/seal (safety head) Stripper Bowl Annular Stripper HYDR. HYDR. Stripper Rørventil I will briefly go into more detail of the BOP arrangments used for a Snubbing Operation as this (rightly) is normally one of the main concerns of operating in wells under pressure. As the well is live and there is no ‘primary’ well control from the hydrostatic head of a kill fluid the ‘stripping BOPs’ take on this role. The stripping arrangements vary between applications but will generally consist of a stripping rubber and bowl situated imediately beneath the jack or work-window, plus two sets of stripping rams to allow for ram to ram stripping if pressures are too high for the stripping rubber. HYDR. Tette og kutte ventil Rørventil Tette og kutte ventil

11 Jekk hoved komponenter
Gin pole med counterbalance vinsjer Travelling slips Tong arm “Pipe ligth” slips Kontrollpanel Power tong “Pipe heavy” slips Arbeidsbasket Jekk sylinder Stationary slips Arbeids vindu Stripper rubber/Bowl

12 Hydraulisk jekk De primære komponentene i den hydrauliske jekken er sylindere, de mest vanlige består av fire sylindere. Løftekapasiteten er avhengig av: Antall sylindere Størrelsen på sylindrene Hydraulisk trykk

13 Lederør (guide tubing)teleskoprør
Monteres inne i jekken for å hindre bøying under store kompresjons belastninger.

14 Arbeidsvindu Er plassert under jekken. Hovedfunksjonen er å gi tilkomst, slik at stripper gummien kan skiftes. For å hindre bøying av snubberøret er det montert lederør gjennom vinduet.

15 Arbeidsplattform Arbeidsbasketen er plassert på den øverste delen av jekken. Det er arbeidsplassen for: Jekk operatør BOP operatør Tang operatør

16 Cameroon D annular BOP Annular preventer er en bop som tetter rundt alle rørdiametre

17 Cameron U BOP BOP som kan inneholde forskjellige typer rams

18 Cameron U BOP pipe ram Pipe ram
Disse monteres nedenfor stripper rams, og brukes for å sikre brønnen ved svikt i stripper rams eller forandring i utstyret ovenfor.Antallet pipe rams kan variere med forholdene. Minst en av dem må kunne styres fra jekkens operasjonsplattform.

19 Stripper gummi Fordeler Lett å operere Lett å bytte Lave kostnader
Ulemper Trykkgrense på 3000 psi Må skiftes regelmessig Stor slitasje i gassbrønner

20 Pipedekk statfjord B WORKSTRING CATWALK BOP SKIDS TOOLCONTAINERS
POWER PACKS ACCUMULATOR RACKS


Laste ned ppt "Bilder fra 2 – 7 viser hovedkomponentene i en snubbing opprigg."

Liknende presentasjoner


Annonser fra Google